House Inspections

Are you considering buying  a house? A pre-purchase home inspection takes the fear out of buying a home and can eliminate any unpleasant surprises. We recommend you learn as much as you possibly can, including general maintenance issues and also matters that may need repairing. Before you buy a home, it’s a good idea to make sure everything is as it should be. There’s no better feeling than knowing the home you’ve just bought is structurally safe and sound and that you’re not going to run into any issues or problems with it now, or in the near future.

All our pre-purchase inspections are conducted by a fully insured & licensed building inspectors with a wealth of knowledge available to help make the whole process very smooth & to give you confidence in the property you are about to purchase.

Property information Site

  • driveway condition
  • paths
  • surfrace drainage
  • fences
  • entry porch
  • shed

Roofing

  • attic and roof timbers
  • gutters and down-pipes
  • eaves
  • fascia and barge boards

General plumbing

Exterior

  • garage – carport
  • pergola – veranda

Interiors

  • bathroom(s)
  • kitchen
  • laundry
  • subfloor

Conclusion and Summary

Interior of the Building

  • Ceilings
  • Walls
  • Floors
  • Windows and Window Frames
  • Doors and Door Frames
  • Plastering
  • Painting
  • Bathrooms, En-suites, Kitchen, Laundry, WC
  • Stairs
  • Balustrades and Handrails
  • Toilets
  • Baths
  • Shower recess
  • Basins
  • Taps
  • Bench tops
  • Cabinets
  • Tiling
  • Plumbing Fixtures and Fittings
  • Hot Water Units
  • Rising Damp
  • Moisture in wet areas
  • Roof space framing structures

Handover / Practical Completion Inspection (PCI), Including New House & Land Packages, and Stage Inspection

 

We strongly recommended that independent building inspections are carried out at certain construction stages, to ensure the quality of construction work undertaken is not being compromised or defective.  The following inspections are recommended:

Construction – Handover Inspection / Practical Completion

All minor defects and minor omissions identified or otherwise should be recorded on an appropriate, signed defects document, and the dwelling should be reasonably suitable for habitation. The contractor must provide the owner with certificates of inspections and warranties, including the final certificate issued by the Building Certifier.

At the time of practical completion a defects document would have been completed as follows:

 

  • List the minor defects and minor omissions that both the contractor and home owner agree to;
  • State when the contractor will attend to those matters;
  • List minor defects or minor omissions that only the home owner believes exist; and
  • Be signed by the home owner and the contractor (or only signed by the contractor where the contractor has made all reasonable efforts to have owner sign).

The contractor is required to correct non-structural defects within 12 months after completion of the dwelling.  Non-structural defects or omissions discovered within the 12 month period can be referred to the contractor in writing for attention within a reasonable time frame.  It is imperative that all communication is in writing as far as practicable, is signed and dated, and copies of all correspondence retained for record.  When contractors fail to address and rectify defects to a satisfactory outcome you may be able to access your local state building commission complaints process for further assistance.

Note:  Structural defects should not even get to handover/practical completion stage as these should be addressed before that time.

Practical Completion / Handover stage is reached when the building under construction is basically ready for handover, including: Full electrical fit-out, full plumbing fit-out, all tiling fully completed, shower screen fitted, final fitting and fixtures installed (towel rails, TP holders, doors stoppers, catches, etc), ceiling insulation, internal paint work, appliances and white goods, pergola’s, fences, external concrete or pavements, rain water tank, finishing of retaining wall/s, landscaping, site drainage, letter box, external paintwork, carpets, blinds, all items connected and operational, all within the confines of the contract agreement.  Only after these stages have been reached is the building ready for a handover inspection or practical completion inspection.

Construction – Footing Inspection

A typical Footing Inspection requires the inspector to inspect footing preparation prior to pouring of concrete. Footings are the lower structural building element which rest directly on the foundation material and once poured are basically inaccessible. It is imperative that footing preparations are carried are diligently and fully compliant with engineers plans and specification. Serious errors in footings can cause a disastrous outcome, which sometimes may not come to light until years later.

For peace of mind, a Footing Inspection prior to pouring concrete is strongly recommended. A typical Footing Inspection will tell you about deficiencies, defects, and items of non-compliance, including issues relating to: excavation, footing dimensions, steel reinforcement dimension and placement, reinforcement supports, clearances at footing penetrations by service pipes. All reinforcement, when necessary, should also be secured and tied at lap and/or splice joints. Note: Concreting contractors should place concrete carefully as not to displace reinforcement or cause concrete segregation. All concrete should be of specified mix, consistency, and compacted when poured, in accordance with engineer’s recommendations.

Construction – Slab Inspection

A typical Floor Slab Inspection requires the inspector to inspect floor slab preparation prior to pouring of concrete. Floor slabs also are part of the lower structural building elements which often gain support from footings and foundation materials and are often integrated with footings. It is imperative that floor slab preparations are carried are diligently and fully compliant with engineers plans and specification. Serious errors in floor slabs can cause a disastrous outcome, which sometimes may not come to light until years later.

For peace of mind, a Slab Inspection prior to pouring concrete is strongly recommended. At slab Inspection will tell you about deficiencies, defects, and issues of non-compliance, including: moisture membranes, steel reinforcement dimension and placement, support, clearances of slab penetrations by service pipes and termite protection barrier provisions. Where required, all reinforcement should also be secured and tied at lap and/or splice joints. Note: Concreting contractors should place concrete carefully as not to displace reinforcement or cause concrete segregation. All concrete should be of specified mix, consistency, and compacted when poured, in accordance with engineer’s recommendations.

Construction – Frame Inspection

A typical Frame Inspection requires the inspector to inspect the structural frame work of the building for standard of workmanship, and compliance.

For peace of mind, a Frame Inspections is strongly recommended and imperative for ensuring that the building frame structure is sound and meets design requirements.

An inspection will tell you about deficiencies, defects, and issues relating to non-conformances. Inspections focus is on structural material compliance, stress grades, wind braces, lintel and lintel supports, point loads, horizontal wind beams, load transfer connections to roof and/or floor diaphragm, tie-down, ceiling height, framing secure and straight.

Construction – Lock-up Inspection

Lock-up inspections are sometimes called for when the project is performing less than satisfactory, and standard of work is questioned. For a well performing builder a lock-up inspection may not be necessary, whereas a poorly performing builder a lock-up inspection may be recommended.

A typical lock-up inspection is generally carried out once the builder has completed the following enclosure stages: Fascia boards, roof guttering, roof covering, roof flashings, external wall cladding including brickwork, external windows & doors, plumbing rough-in, wiring. Note: pointing of roof tiles or scribing of metal roof capping and screws may not necessarily be completed. The lock-up inspection should provide the inspector with an opportunity to sight and inspect wall cavities, brick ties, wall flashings, window and external door flashings, prior to internal wall covering.

Construction – Fixing Stage

Fixing stage inspections are sometimes called for when the project is performing less than satisfactory, and standard of work is questioned. For a well performing builder a fixing stage inspection may not be necessary, whereas a poorly performing builder a fixing stage inspection may be recommended.

A typical fixing stage inspection is generally carried out once the builder has reached pre-painting stage, which includes: wet area seal, internal linings, cornices, jambs, architraves, skirtings, doors, locks, tiling, built-in cupboards, shelving, cabinets, basins, vanity units, troughs, sink, soffit linings, plumbing ready for final fitting, drainage connections, electrical ready for final fittings, external wall finishes. Note: Provided the building is lockable the garage door/s does not necessarily have to be installed at this stage.

The fixing stage inspection should provide the inspector with an opportunity to sight and assess finishes prior to application of paint.

We recommended that when you enter into a building construction contract that you stipulate in the contract that independent inspections will be carried out at certain construction stages by an inspector of your choice.  If you are not sure, ask your Solicitor.

Exterior of the Building

  • Roof coverings
  • Gutters
  • Skylights
  • Vents and Flues
  • Flashings
  • Valleys
  • Eaves
  • Fascias and Barges
  • Downpipes
  • Insulation
  • Downlight safety
  • Sarking
  • Subfloor supports
  • Ventilation
  • Drainage
  • Piers
  • Exterior walls including Cladding
  • lintels
  • Doors
  • Windows
  • Pergolas
  • Decking
  • Patios
  • Balconies
  • With in 30m of the house and within the boundaries of the site
  • Fencing
  • Retaining walls
  • Paths
  • Driveways and water drainage
  • Garages
  • Sheds
  • Detached Laundry

Your Name (required)

Your Email (required)

Phone

Subject (required)

Have a question regarding building inspections? Are you ready to engage a professional, licensed building inspector to provide you with peace of mind? Contact Thuso Othusitse and the team of Evolve Group using the form provided or direct on our details below.

Thuso Othusitse

+267 71460422
+267 398 0404

othusitse@evolvegroup.co.bw